产品详情
简单介绍:
日本PEACOCK孔雀量表C-700数显电子计数器日本PEACOCK孔雀量表C-700数显电子计数器
详情介绍:
-
Equipped with large display functions and various measurement functions our Digital Counters
can be installed in a Control Panel or placed on a desk due to their compact designs.Specifications of Digital Counters Model C-500 C-700 Displayed digits Selection of 10?m Selection of 1?m Display -9999.99 -- 00.00 -- 9999.99 -999.999 -- 0.000 -- 999.999 High-luminance LED display with 7 segments (red) Power supply voltage
& power consumptionAC100V -- AC240V
/ 9VA or lowerOperating temperature 0 -- +40?C Compatible Linear Gauges Selection of 10?m display Selection of 1?m display DL-2 D-5 D-10 D-20 D-30 D-50 D-100 DN-10 DN-20 D-5UZ DL-2S D-5S D-10S D-20S D-30S D-50S D-100S DN-10S DN-20S Accessories AC power cord (2m) ; One cord Metal fittings for panel installation ; Two units ( to be used for installation in panel and securing stand fittings ) Stand fittings ; One unit ( to be used when counter is used as desktop device ) Terminal block functions
( Rear panel )Terminal block --> Screwless terminal block Usable electric cables --> AWG22 - 28 Length of peeled wire of cables --> 8 - 9mm Pin alignment (*1) St/Sp Controls "START" and "STOP" of MAX MIN P-P
measurement mode.(*2) React Controls "SUSPEND" and "START" of P-P
measurement mode.3 Latch Controls "LATCH" and "CANCEL" of measured value. 4 Reset External "RESET"
"PRESET" ( Function available only in Model No. C-700 )5 Alarm Error signal output Max
DisplayMin
DisplayP-P
Display(*6) -NG Outputs -NG based on
OK±NG judgment (red LED).--> +NG(2) -NG(1) NG(2) (*7) OK Outputs OK based on
OK±NG judgment (green LED).--> OK OK OK (*8) +NG Outputs +NG based on
OK±NG judgment (orange LED).--> +NG(1) -NG(2) NG(1) (1) : NG output in first stage
(2) : NG output in second stage9 GND GND (* ) Circled numbers indicate functions available only in Model No. C-700 Dip sw setting functions
( Printed circuit board )Dip(1) Dip(2) SW 1 Select 1?m or 10?m SW 1 Settings by Manufacturer SW 2 Select direction of
counting.SW 2 Select whether or not to include
default values for OK±NG judgment.SW 3 Select activation or non-
activation of error output.SW 3 Select either "orthogonal" or "sine"
for input waveform.SW 4 Select activation or non-
activation of overflow.SW 4 Select either 400msec or 100msec
for RESET time.Data output (RS-232C)
D-Sub9P plug
INCH screwOptions Excel input software BCD output board Pin Alignment 1 NC -- Communication mode ; Half-duplexasynchronouscommunication 2 Rxd in <-- Communication speed ; 9600bps 3 Txd --> out Format ; 7Bit ASCI I 4 NC -- Parity ; even number 5 SG -- Stop bit ; 1Bit 6 NC -- RTS / CTS ; Returned when not in use. 7 RTS --> out Reception command ; Transmission request ASCI I [T] [t] 8 CTS in <-- ; Reset ASCI I [R] [r] 9 NC -- Connection cables ; Cross cables ( not included )
PK-2002 ; Data imported into Excel cells from RS-232C output. CB-BCD ; Cannot be used in combination with RS-232C output. Display functions 1/1 display --> Displays the measured value as is. 1/2 display --> Displays the measured value after halving it. ×2 display --> Displays the measured value after doubling it.
With 1?m display and ×2 display the lowest digit will be displayed as an even number.Presetting display function Zero setting only Can display preset values Measurement mode function
[MAX] [MIN] [P-P]--- Current value display Maximum
value (Max)RESET action is taken by
ST of the ST/SP control
terminal.Minimum
value (Min)Deflection
(P-P)OK±NG judgment function
( Refer to terminal output
circuit )--- Current
value mode+NG OK -NG Maximum
value modeOK +NG (1) +NG (2) Minimum
value modeOK -NG (1) -NG (2) Deflection
modeOK NG (1) NG (2) Dimensions / Weight 144(W)×72(H)×160(D)mm / 950g
Time Chart [ Model No. C-700 ]
Control Terminal Input Circuit
Pin **** ST/SP Pin NO.2 REACT Pin NO.3 LATCH Pin NO.4 RESET
Terminal Output Circuit
Pin NO.5 ALARM Pin NO.6 -NG Pin NO.7 OK Pin NO.8 +NG
| Page Top |
Dimension of Digital Counters ( C-500 C-700 )
Panel cutting dimensions ; Panel thickness ( t = 1.6 - 3.2mm )